![how to write network path in log shipping how to write network path in log shipping](https://cdn.ssltrust.com.au/assets/images/help/wireshark-guide/wireshark-network-analyzer.png)
- #How to write network path in log shipping windows 10#
- #How to write network path in log shipping windows#
Try to disable the IPv6 protocol in the properties of your network adapter in the Control Panel.Try to change the computer name in the System properties.Try to temporarily disable your antivirus and/or firewall application and check if the problem persists while accessing the network resources.Function Discovery Resource Publication – FDResPub.Function Discovery Provider Host – fdPHost.Try to start these services and change startup type to the Automatic Delayed Start: Verify that the following services are running on your computer (open the services.msc console).If you simultaneously have two active network interfaces on your device (Wi-Fi and Ethernet), try to temporarily disable one of them and check access to your local network resources.To do this, enter \\192.168.1.100 in the File Explorer and press Enter (replace with the IP address of your network storage or remote computer) Check if the network storage (computer with a shared folder) is accessible by an IP address.In the properties of the shared network folder (both on the NTFS file system permissions and the shared folder level), verify that the Everyone group has the permissions to read the contents of the folder.In the All Networks section, enable the following options: Turn on network discovery + Turn on automatic setup of network connected devices.Make sure that the following options are enabled: In the Network and Sharing Center section of the Control Panel on both computers, verify that the Private network profile is used as the current profile ( Private (Current profile)).
#How to write network path in log shipping windows#
If your computers are joined to a workgroup, I strongly advise you to follow the recommendations from the article Network computers not showing in Windows 10.
#How to write network path in log shipping windows 10#
Get-SmbServerConfiguration | select "*enablesmb*"|fl EnableSMB1Protocol : FalseĬheck the Network Discovery Configuration on Windows 10 You can verify that the SMB 1 and SMB 2 protocols are disabled by running the following PowerShell command: Set-SmbServerConfiguration –EnableSMB2Protocol $true Reg.exe add "HKLM\SYSTEM\CurrentControlSet\services\LanmanServer\Parameters" /v "SMB2" /t REG_DWORD /d "0" /f Sc.exe config lanmanworkstation depend= bowser/mrxsmb10/nsiĭism /online /Disable-Feature /FeatureName:"SMB1Protocol" The fact is that your computer may try to use the SMB 2.0 protocol to access network folders that allow only SMB 3.0 connections (possibly with traffic encryption).įirst disable the SMB v1.0 protocol through the Control Panel or using the commands in the PowerShell console:
![how to write network path in log shipping how to write network path in log shipping](https://mostafaelmasry.files.wordpress.com/2013/01/22.png)
![how to write network path in log shipping how to write network path in log shipping](https://cdn.ttgtmedia.com/digitalguide/images/Misc/log_shipping_4.jpg)
If only SMB v3 devices are used on your network (Windows 8.1 / Windows Server 2012 R2 and newer, see the table of SMB versions in Windows), you can fix the 0x80070035 error by disabling legacy SMB1 and SMB2 protocols. Reg add HKLM\SYSTEM\CurrentControlSet\Services\LanmanWorkstation\Parameters /v AllowInsecureGuestAuth /t reg_dword /d 00000001 /f Disable SMB1 and SMB2 Protocols in Windows Or you can enable SMB network access under guest account via the registry using the command: In addition, you can access the features installation dialog by running the optionalfeatures.exe command. You can enable the legacy SMB client to access network devices using SMBv1 protocol via the Control Panel (Control Panel -> Programs and Features -> Turn Windows features on or off -> SMB 1.0 / CIFS File Sharing Support -> SMB 1.0 / CIFS Client).
![how to write network path in log shipping how to write network path in log shipping](http://www.sqlserverlog.com/wp-content/uploads/2015/06/4_Transaction-Log-Backup-Settings.jpg)
To check if the SMBv1 protocol is enabled in Windows 10, use the following command:ĭism /online /Get-Features /format:table | find "SMB1Protocol"Īs you can see, in this case the SMB1Protocol-Client feature is disabled. And when accessing the resource by the UNC path ( \\NASname), you can receive the error “0x80070035”. If you try to connect to a network device that only supports access over SMBv1 protocol (for example, an old version of NAS storage, a computer running Windows XP/Windows Server 2003) from the latest Windows 10 builds, you won’t be able to connect to shared network folders on such a device. SMBv1 is not Installed by Default in Windows 10įirst of all, you need to understand whether the problem is related to the fact that in Windand newer the unsafe legacy SMB v1.0 protocol is disabled by default (this protocol is used to access network shared files and folders in local network).